Security Centres TS2000 Uživatelský manuál stáhnout pdf (Strana 4)

260

288

310

Power size 5

135

Power size 2

Power size 4

310

285

260

Power size 4

Power size 5

Power size 2

135

¾Mark the fixing positions in accordance with fixing dimensions (see figure 1 and 2

above.) There are three holes to be drilled/tapped on the door leaf for the closer body and

four holes to be drilled/tapped on the underside of the transom for the parallel arm bracket.

¾Separate the primary and secondary arms. This can be done using a screwdriver as a

lever. The arm sections will snap together and apart. Secure the primary arm to the spindle

using M6 allen bolt supplied. Ensure splines are interlocked. Locate arm at approx. 10°

towards the rear of the closer. (See figure 3 and 4.) Turn closing speed valve, located on

the front of the body of the closer fully clockwise. This will decrease the closing speed to

almost zero. Do not overtighten. Rotate primary arm to approximately 90°. (See figure 5

and 6.) Secure closer body to door leaf with fixings provided, making sure that the spindle

is positioned away from the hinge side. (See figure 1 and 2 above.) The power size

(closing force) of the TS2000 is not adjustable in this configuration and the unit must be

mounted using the centre fixing holes. Secure primary and secondary arms together

(simply click in place.)

¾Rotate primary arm in direction of travel (away from door leaf) until an angle of approx. 2°

is reached in relation to the door leaf. (See figure 7 and 8.) Tighten 10mm locking bolt.

¾TS2000 only. For TS2000 BC see below. If latch action is required (to overcome a latch

or seals) fit closer as described above.

¾TS2000 only. For TS2000 BC see below. If no latch action is required. Fit closer as

described above. Separate the primary and secondary arms. Turn closing speed valve,

located on the front of the body of the closer fully clockwise. This will decrease the closing

speed to almost zero. Do not overtighten. Rotate the primary arm approx. 90° in the

direction of travel (roughly perpendicular to the door leaf.) Loosen the M6 allen bolt

securing the primary arm to the closer body enough to enable adjustment. Rotate the

primary arm 1 notch of the splined spindle in the opposite direction of travel. Re-tighten

M6 allen bolt securing the primary arm to the closer body. Loosen 10mm locking bolt on

secondary arm and re-connect primary and secondary arms. Re-adjust the closing speed.

Rotate primary arm in direction of travel (away from door leaf) until an angle of approx. 2°

is reached in relation to the door leaf. (See figure 7 and 8.) Tighten the 10mm locking bolt.

If on testing the latch action has not been removed repeat above until adjusted

satisfactorily.

¾TS2000 BC. Note: If backcheck is required to come in at any opening angle less than

100° then latch action is not possible with this unit.

•The back check is a segment of the closers opening cycle with increased resistance. In

this configuration it is factory set to come in when the door is at approx. 100°. In order to

bring this in earlier fit closer as described above. Separate the primary and secondary

arms. Turn closing speed valve, located on the front of the body of the closer fully

clockwise. This will decrease the closing speed to almost zero. Do not overtighten. Rotate

the primary arm approx. 90° in the direction of travel (roughly perpendicular to the door

leaf.) Loosen the M6 allen bolt securing the primary arm to the closer body enough to

enable adjustment. Rotate the primary arm 1 notch of the splined spindle in the opposite

direction of travel. Re-tighten M6 allen bolt securing the primary arm to the closer body.

Loosen 10mm locking bolt on secondary arm and re-connect primary and secondary arms.

Re-adjust the closing speed. Rotate primary arm in direction of travel (away from door leaf)

until an angle of approx. 2° is reached in relation to the door leaf. (See figure 5 and 6.)

Tighten the 10mm locking bolt. If on testing the back check is still not early enough repeat

above until adjusted satisfactorily

•If the unit has not been adjusted to bring the backcheck in earlier then the latch action of

the TS2000 BC can now be adjusted using the adjustment valve located on the front of the

body of the closer next to the closing speed adjustment valve. Clockwise will decrease the

latch action and anticlockwise will increase the latch action. Do not overtighten.

¾The closing speed can now be adjusted using the adjustment valve located on the front

of the body of the closer. Clockwise will decrease the closing speed and anticlockwise will

increase the closing speed. Do not overtighten.

Fixing in figure 66

1 2 3 4 5 6

Komentáře k této Příručce

Žádné komentáře

Security Centres TS2000 Uživatelský manuál Strana 4

Komentáře k této Příručce