Security Centres TS2000 Uživatelský manuál stáhnout pdf (Strana 2)

Fig3

Fig4

Fig5

90°

Fixing in figure 1

222

344

319Power size 4

Power size 2

294

Power size 5

135

130

135

222

130

344

319

294

Power size 5

Power size 4

Power size 2

¾With the aid of the template mark out the fixing positions. Align the hinge point of the

template with the centre line of the hinge on the door. (This applies to both left and right-hand

doors.) There are two holes to be drilled/tapped on the transom for the arm shoe and three

holes to be drilled/tapped on the door leaf for the closer body. If the template is not used refer

to fixing dimensions (see figure 1 and 2 above.)

¾Secure closer body with screws provided, making sure that the spindle is positioned

towards the hinge side. (See figure 1 and 2 above.) The power size (closing force) of the

TS2000 is adjusted by moving the body of the closer either towards or away from the hinge

point. The three holes that have been drilled for the closer body relate to three of the nine

fixing holes on the closer. In order to fit the closer to a specific power size simply select the

correct fixing holes as indicated on the body of the closer and fit.

¾TS2000 only. For TS2000 BC see below. If latch action is required (to overcome a latch or

seals.) Separate the primary and secondary arms. This can be done using a screwdriver as a

lever. The arm sections will snap together and apart. Secure the primary arm to the spindle

using M6 allen bolt supplied. Ensure splines are interlocked. Locate arm at approx. 80° with

respect to the door leaf, towards the hinge point. (See figure 3.) Fix the secondary arm to the

transom using the screws provided and loosen 10mm locking bolt on arm. Secure primary

and secondary arms together (simply click in place.) Prime the closer slightly by rotating the

primary arm to approx. 90° with respect to the door leaf and tighten the locking bolt. (See

figure 4.)

¾TS2000 only. For TS2000 BC see below. If no latch action is required. As above however

when priming the closer rotate the secondary arm to approx. 90° with respect to the door

leaf and tighten the locking bolt. (See figure 5.)

¾TS2000 BC. Secure the primary arm to the spindle using M6 allen bolt supplied. Ensure

splines are interlocked. Locate arm at approx. 80° with respect to the door leaf, towards the

hinge point. (See figure 3.) Fix the secondary arm to the transom using the screws provided

and loosen 10mm locking bolt on arm. Secure primary and secondary arms together (simply

click in place.) Prime the closer slightly by rotating the primary arm to approx. 90° with

respect to the door leaf and tighten the locking bolt.

• The back check is a segment of the closers opening cycle with increased resistance. It is

factory set to come in when the door is at approx. 80°. In order to bring this in earlier

disengage the primary and secondary arms. Loosen the M6 allen bolt securing the primary

arm to the closer enough to enable adjustment. Rotate the primary arm 1 notch of the splined

spindle in the opposite direction to travel. Re-tighten M6 allen bolt securing the primary arm

to the closer body. Loosen 10mm locking bolt on secondary arm and re-connect primary and

secondary arms. Prime the closer by rotating the primary arm to approx. 90° with respect to

the door leaf and tighten the 10mm locking bolt. If on testing the back check is still not early

enough repeat above until adjusted satisfactorily.

•The latch action of the TS2000 BC can now be adjusted using the adjustment valve located

on the front of the body of the closer next to the closing speed adjustment valve. Clockwise

will decrease the latch action and anticlockwise will increase the latch action. Do not

overtighten.

¾The closing speed can now be adjusted using the adjustment valve located on the front of

the body of the closer. Clockwise will decrease the closing speed and anticlockwise will

increase the closing speed. Do not overtighten.

¾Test installation by simulating persons using the entrance. The door should close smoothly

without slamming and present no potential hazard to traffic.

1 2 3 4 5 6

Komentáře k této Příručce

Žádné komentáře

Security Centres TS2000 Uživatelský manuál Strana 2

Komentáře k této Příručce