Security Centres TS2000 Uživatelský manuál stáhnout pdf (Strana 3)

4438

222

294

319

344

Power size 5

Power size 2

Power size 4

135

130

222

344

Power size 5

319

294

Power size 2

130

Power size 4

135

Fig3

Fig4

Fig5

Fixing in figure 61

¾With the aid of the template mark out the fixing positions. Align the hinge point of the template

with the centre line of the hinge on the door. (This applies to both left and right-hand doors.) There

are two holes to be drilled/tapped on the door leaf for the arm shoe and three holes to be

drilled/tapped on the transom for the closer body. If the template is not used refer to fixing

dimensions (see figure 1 and 2 above.)

¾Secure closer body with screws provided, making sure that the spindle is positioned towards the

hinge side. (See figure 1 and 2 above.) The power size (closing force) of the TS2000 is adjusted by

moving the body of the closer either towards or away from the hinge point. The three holes that

have been drilled for the closer body relate to three of the nine fixing holes on the closer. In order

to fit the closer to a specific power size simply select the correct fixing holes as indicated on the

body of the closer and fit.

¾TS2000 only. For TS2000 BC see below. If latch action is required (to overcome a latch or

seals.) Separate the primary and secondary arms. This can be done using a screwdriver as a

lever. The arm sections will snap together and apart. Secure the primary arm to the spindle using

M6 allen bolt supplied. Ensure splines are interlocked. Locate arm at approx. 80° with respect to

the transom, towards the hinge point. (See figure 3.) Fix the secondary arm to the door leaf using

the screws provided and loosen 10mm locking bolt on arm. Secure primary and secondary arms

together (simply click in place.) Prime the closer slightly by rotating the primary arm to approx. 90°

with respect to the door leaf and tighten the locking bolt. (See figure 4.)

¾TS2000 only. For TS2000 BC see below. If no latch action is required. As above however when

priming the closer rotate the secondary arm to approx. 90° with respect to the door leaf and

tighten the locking bolt. (See figure 5.)

¾TS2000 BC. Secure the primary arm to the spindle using M6 allen bolt supplied. Ensure splines

are interlocked. Locate arm at approx. 80° with respect to the transom, towards the hinge point.

(See figure 3.) Fix the secondary arm to the door leaf using the screws provided and loosen 10mm

locking bolt on arm. Secure primary and secondary arms together (simply click in place.) Prime the

closer slightly by rotating the primary arm to approx. 90° with respect to the door leaf and tighten

the locking bolt.

• The back check is a segment of the closers opening cycle with increased resistance. It is factory

set to come in when the door is at approx. 80°. In order to bring this in earlier disengage the

primary and secondary arms. Loosen the M6 allen bolt securing the primary arm to the closer

enough to enable adjustment. Rotate the primary arm 1 notch of the splined spindle in the opposite

direction to travel. Re-tighten M6 allen bolt securing the primary arm to the closer body. Loosen

10mm locking bolt on secondary arm and re-connect primary and secondary arms. Prime the

closer by rotating the primary arm to approx. 90° with respect to the door leaf and tighten the

10mm locking bolt. If on testing the back check is still not early enough repeat above until adjusted

satisfactorily.

•The latch action of the TS2000 BC can now be adjusted using the adjustment valve located on

the front of the body of the closer next to the closing speed adjustment valve. Clockwise will

decrease the latch action and anticlockwise will increase the latch action. Do not overtighten.

¾The closing speed can now be adjusted using the adjustment valve located on the front of the

body of the closer. Clockwise will decrease the closing speed and anticlockwise will increase the

closing speed. Do not overtighten.

¾Test installation by simulating persons using the entrance. The door should close smoothly

without slamming and present no potential hazard to traffic.

1 2 3 4 5 6

Komentáře k této Příručce

Žádné komentáře

Security Centres TS2000 Uživatelský manuál Strana 3

Komentáře k této Příručce